Parts for Kenmore Models 6440A REV J

Water inlet valve with mounting bracket (valve)

The water fill valve kit attaches the water lines on the back of your washer. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed. This kit includes a blue body fill valve, a mounting bracket and a screw. The valve body of this part could be blue or green in color. There are two ports for water to enter, and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads. This is a genuine OEM part. Please remember to disconnect the power and the water supply before starting your repair.

Easy Part #:: EAP334646

Availability:: In Stock

Price:: $32.08

Water valve with guard (valve - wr57x10032)

This double inlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.

Easy Part #:: EAP16226572

Availability:: In Stock

Price:: $76.66

Grease filter

The grease filter is intended for use with some downdraft cooktops and ranges to collect grease particles in the air from cooking. The grease filter is silver in color, approximately 15 1/2” long and almost 6 1/4” wide. As per the manufacturer, the original filter may have been a 1/2” wider, but it should not be a problem and will still function the same. The grease filter is sold individually and is a genuine OEM part.

Easy Part #:: EAP11743870

Availability:: In Stock

Price:: $26.10

Burner knob (knob (brushed chrome))

Sold Individually. This knob accepts a double flat shaft.

Easy Part #:: EAP11744413

Availability:: In Stock

Price:: $33.37

Burner grate pads - kit of 5 (foot, grate (rubber))

These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.

Easy Part #:: EAP389174

Availability:: In Stock

Price:: $8.94

Refrigerator pantry drawer door cover (pantry lid assy)

The pantry drawer lid helps keep everything inside the drawer, it acts as a cover and keeps your drawer at the proper temperature by creating a seal. If the door will not open or close, or if the drawer section is too cold, you may need to replace the lid. The pantry drawer lid is a genuine OEM part.

Easy Part #:: EAP11723190

Availability:: In Stock

Price:: $95.98

Lower bake element (element, bake (lower))

The bake element is located on the bottom of the oven cavity to supply heat for baking. The element terminals are male quarter inch spade connectors and have push on wire terminals. This element measures 19 inches wide by 20 inches long, including the terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Easy Part #:: EAP11744518

Availability:: In Stock

Price:: $47.95

Center rail (rail, center crisper)

This is the center support rail for the refrigerator crisper drawer. This rail supports center of the crisper frame.

Easy Part #:: EAP11752912

Availability:: In Stock

Price:: $23.17

Evaporator fan motor

This 115-volt 60Hz evaporator fan motor is located in the back of the freezer and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. If the motor has failed, the freezer/refrigerator will become too warm because the fan motor is not circulating the cool air from the freezer into the refrigerator. This is a genuine OEM part. Please remember to disconnect the power to the appliance before starting your repair.

Easy Part #:: EAP12741350

Availability:: In Stock

Price:: $59.56

Igniter kit (dryer burner igniter kit)

This silicon carbide igniter with ceramic holder kit includes the 3-inch flat igniter, mounting bracket, 4-inch wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers. This part ignites the gas within the dryer to heat the dryer during the cycle, so if your dryer takes too long to dry, has no heat or not enough heat, you may need to replace the igniter. Be sure to disconnect the power source from your dryer before you do this repair. The igniter is very fragile and should be handled with care.

Easy Part #:: EAP334180

Availability:: In Stock

Price:: $34.93

Thermal cut-off kit (cutoff-tml)

This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.

Easy Part #:: EAP334278

Availability:: In Stock

Price:: $40.19

Bake element - push on terminals - 240v (bake element)

The bake element is located on the bottom of the oven with male spade terminals and push-on terminals. The bake element provides heat for baking. If your oven is too hot, not heating evenly, element is not heating, or little to no heat when baking, you may need to replace your bake element. This is a genuine OEM part. Please remember to disconnect the power to the range before starting your repair.

Easy Part #:: EAP249238

Availability:: In Stock

Price:: $82.03

Shelf retainer bar end cap

The door shelf retainer bar end cap helps keep the retainer shelf bar in place to hold items on the door shelves. The end cap can be used for the left or right side of the door. This door end cap is almost two inches long, white in color, made entirely of plastic, and sold individually. This is a genuine OEM part.

Easy Part #:: EAP11743131

Availability:: In Stock

Price:: $18.27

Lower wheel assembly (wheel assembly (lwr))

The rack wheel and axle attach to the lower rack to allow you to slide the rack in and out easily. If your dish rack is not moving in and out of the dishwasher properly, you may have a broken or missing wheel and it will need to be replaced. The wheel and axle are white in color, made of plastic, and sold individually. This is a genuine OEM part kit.

Easy Part #:: EAP11747717

Availability:: In Stock

Price:: $11.60

Mounting bracket (dishwasher mounting bracket)

The mounting bracket is used to attach the dishwasher to the underside of the counter. The mounting bracket holds the dishwasher in place to keep it from moving during cycles and to keep the dishwasher level. The bracket is made of metal and is approximately 3” in length. The screws are not included with the bracket, they must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and the water supply to the dishwasher before starting the repair.